Home / Builds / 240 Under-Table Kit 3W-2H

MODULITH 240 Under-Table Kit 3W-2H

Name: MODULITH 240 Under-Table Kit 3W-2H
Brand: MODULITH
SKU: build:240-undertable-3w2h
Availability: InStock

formerly GEN2

FREE 240 CollectionOfficial build

Assembly help: the Under-Table Rails guide walks the install step by step.

Render of the assembled MODULITH 240 Under-Table Kit 3W-2H

Five deep drawers under the table for hand tools, cables, tape and craft supplies - three narrow cases on top, a wide and a narrow below.

Drawers	5
To print	43 pieces in 35 print jobs (the Planner shows 47: it also counts 4 optional Side Covers, a finish for the end walls that the kit count leaves out)
Required hardware	10 countersunk wood screws, #6 × 3/4 inch by default. That screw reaches about 16 mm into the top, so check the top is thick enough and choose a length that cannot break through. The magnets in the list are an optional upgrade, only if you add the magnetic closure.
Load rating	None published, so judge what you store in it and check the fixings yourself. Narrow cases go on top because the case walls nearest the support carry hanging weight better; that is design guidance, not a load test.
Overall assembled size	264 × 119 × 269 mm (W × H × D, measured with the rail and faceplates, without the optional side covers)
Filament and time	About 1457 g of filament and 46 h 50 min of printing for every part in the kit as listed below. In one filament that is 2 × 1 kg spools. Each extra colour or material starts a spool of its own. From 925 g on a spool, one more is recommended to leave room for purge and failed prints. The optional drawer stoppers are not counted. Summed from the same estimates the part pages show; your slicer will differ.
Collection	240 Collection - inside drawer depth 226 mm

Get the under-table rails

Printables Thangs

This kit has no single download. The under-table rails come from this listing, with every section width in the same download, and every other part below links its own page.

3D assembly guide Open in the Planner

The 3D guide walks every step interactively; the Planner opens this exact layout for resizing or restyling before you print.

Everything in the kit

Each printed part links to its catalog page - the exact files, sizes and a 3D preview. The printed parts and the wood screws make a complete working kit; the magnetic closure (printed clips + purchased magnets) is optional.

Drawers
4 ×	240 Decor Drawer - 1W-1H
1 ×	240 Decor Drawer - 2W-1H
Cases & Extenders
4 ×	240 Case - 1W-1H Cases QuickLock together.
1 ×	240 Case - 2W-1H Cases QuickLock together.
4 ×	240 Side Cover - 1H optional Optional · covers the exposed sides of the outermost cases (pairs to each case's height via the side dovetails). Most popular with Table Top Kits.
Faceplates & Handles
4 ×	Classic Decor Faceplate - 1W-1H
1 ×	Classic Decor Faceplate - 2W-1H
Hardware
5 sets	QuickLock (Left + Right) Included with each case model, or print from the universal Hardware pack.
10 ×	Magnet Insert (10x2mm) (or the 6x2mm variant) required with magnetic closure One clips to the case back, one to the drawer back · the pair meets for a magnetic catch that pulls the drawer shut and holds it. Wider drawers have extra slots if you'd like to add more.
10 ×	Magnets 10×2mm or 6×2mm required with magnetic closure · hardware store Seat in the magnet clips. Standard strength suits most builds · the N52s hold noticeably harder (can be too strong for smaller drawers).
3 pairs	Drawer Stoppers (Left + Right) optional Optional but recommended · a Left + Right pair per 1W stops a drawer from pulling all the way out. They snap into the base of the case above (or the covers over a top row). Under-table top-row drawers don't need them · the rail has stoppers built in.
Mounting
1 ×	240 Under-Table Rail - 2W section All rail widths are in the same download · print the section sizes listed.
1 ×	240 Under-Table Rail - 1W section All rail widths are in the same download · print the section sizes listed.
10 ×	Countersunk wood screws (#6/#8) hardware store Hardware store item · #6 × 3/4" (3.5 × 19 mm) is the default - it reaches about 16 mm into the top, so check the surface is thick enough first and choose a length that cannot break through. Minimum 4 / 6 / 8 / 10 screws per 1W / 2W / 3W / 4W rail section.